FreeBSD 9.0RC3 on Aspire one (FreeBSD 9.0RC3 2011/12/12) [FreeBSD]
Aspire onetにFreeBSD 9.0RC3をインストールしてみました。今回はUSBフラッシュメモリにインストーラをコピーして、そこからインストールしています。半年ぐらいに前にLinuxをインストールしようとした際に同様の手法が使えず、この辺の仕組みはFreeBSDの方が先進的で便利だと感じました。
今回9系をインストールしてみましたが、インストーラCUIが変わってるんですね。最初はちょっと戸惑いました。起動時のキャラクターロゴもFreeBSD デーモンボール?(角の生えたツヤツヤの風船ボールみたいなやつ、見れば分かる)になっていました。とりあえずdmesgです。
前のバージョンではsysctlでCPU温度が拾えたような記憶があったのですが、見えなくなってるみたい。仕様変更かな?
今回9系をインストールしてみましたが、インストーラCUIが変わってるんですね。最初はちょっと戸惑いました。起動時のキャラクターロゴもFreeBSD デーモンボール?(角の生えたツヤツヤの風船ボールみたいなやつ、見れば分かる)になっていました。とりあえずdmesgです。
aspire# dmesg Copyright (c) 1992-2011 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.0-RC3 #0: Sun Dec 4 08:01:02 UTC 2011 root@obrian.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386 CPU: Intel(R) Atom(TM) CPU N270 @ 1.60GHz (1596.03-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x106c2 Family = 6 Model = 1c Stepping = 2 Features=0xbfe9fbffFeatures2=0x40c39d AMD Features2=0x1 TSC: P-state invariant, performance statistics real memory = 1073741824 (1024 MB) avail memory = 1019850752 (972 MB) Event timer "LAPIC" quality 400 ACPI APIC Table: FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs FreeBSD/SMP: 1 package(s) x 1 core(s) x 2 HTT threads cpu0 (BSP): APIC ID: 0 cpu1 (AP/HT): APIC ID: 1 ioapic0: Changing APIC ID to 4 ioapic0 irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: on motherboard acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 900 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 cpu0: on acpi0 cpu1: on acpi0 acpi_ec0: port 0x62,0x66 on acpi0 acpi_button0: on acpi0 acpi_lid0: on acpi0 acpi_button1: on acpi0 battery0: on acpi0 acpi_acad0: on acpi0 pcib0: port 0xcf8-0xcff on acpi0 pci0: on pcib0 vgapci0: port 0x60c0-0x60c7 mem 0x58480000-0x584fffff,0x40000000-0x4fffffff,0x58500000-0x5853ffff irq 16 at device 2.0 on pci0 agp0: on vgapci0 agp0: aperture size is 256M, detected 7932k stolen memory vgapci1: mem 0x58400000-0x5847ffff at device 2.1 on pci0 hdac0: mem 0x58540000-0x58543fff irq 16 at device 27.0 on pci0 pcib1: at device 28.0 on pci0 pci1: on pcib1 pcib2: at device 28.1 on pci0 pci2: on pcib2 re0: port 0x3000-0x30ff mem 0x51010000-0x51010fff,0x51000000-0x5100ffff irq 17 at device 0.0 on pci2 re0: Using 1 MSI-X message re0: Chip rev. 0x24800000 re0: MAC rev. 0x00000000 miibus0: on re0 rlphy0: PHY 1 on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow re0: Ethernet address: 00:11:22:33:44:55 pcib3: at device 28.2 on pci0 pci3: on pcib3 ath0: mem 0x55200000-0x5520ffff irq 18 at device 0.0 on pci3 ath0: AR2425 mac 14.2 RF5424 phy 7.0 pcib4: at device 28.3 on pci0 pcib4: failed to allocate initial I/O port window: 0x1000-0x1fff pci4: on pcib4 pci4: at device 0.0 (no driver attached) pci4: at device 0.2 (no driver attached) pci4: at device 0.3 (no driver attached) pci4: at device 0.4 (no driver attached) uhci0: port 0x6080-0x609f irq 16 at device 29.0 on pci0 uhci0: LegSup = 0x2f00 usbus0: on uhci0 uhci1: port 0x6060-0x607f irq 17 at device 29.1 on pci0 uhci1: LegSup = 0x2f00 usbus1: on uhci1 uhci2: port 0x6040-0x605f irq 18 at device 29.2 on pci0 uhci2: LegSup = 0x2f00 usbus2: on uhci2 uhci3: port 0x6020-0x603f irq 19 at device 29.3 on pci0 uhci3: LegSup = 0x2f00 usbus3: on uhci3 ehci0: mem 0x58544400-0x585447ff irq 16 at device 29.7 on pci0 usbus4: EHCI version 1.0 usbus4: on ehci0 pcib5: at device 30.0 on pci0 pci5: on pcib5 isab0: at device 31.0 on pci0 isa0: on isab0 atapci0: port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x60a0-0x60af irq 17 at device 31.2 on pci0 ata0: on atapci0 ata1: on atapci0 pci0: at device 31.3 (no driver attached) atrtc0: port 0x70-0x77 on acpi0 atrtc0: Warning: Couldn't map I/O. Event timer "RTC" frequency 32768 Hz quality 0 hpet0: iomem 0xfed00000-0xfed003ff irq 0,8 on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 950 Event timer "HPET" frequency 14318180 Hz quality 450 Event timer "HPET1" frequency 14318180 Hz quality 440 Event timer "HPET2" frequency 14318180 Hz quality 440 attimer0: port 0x40-0x43,0x50-0x53 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 atkbdc0: port 0x60,0x64 irq 1 on acpi0 atkbd0: irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model Generic PS/2 mouse, device ID 0 pmtimer0 on isa0 sc0: at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 ppc0: parallel port not found. est0: on cpu0 p4tcc0: on cpu0 est1: on cpu1 p4tcc1: on cpu1 Timecounters tick every 1.000 msec hdac0: HDA Codec #0: Realtek ALC268 pcm0: at cad 0 nid 1 on hdac0 pcm1: at cad 0 nid 1 on hdac0 usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 12Mbps Full Speed USB v1.0 usbus4: 480Mbps High Speed USB v2.0 ugen0.1: at usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1: on usbus1 ugen2.1: at usbus2 uhub2: on usbus2 ugen3.1: at usbus3 uhub3: on usbus3 ugen4.1: at usbus4 uhub4: on usbus4 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub3: 2 ports with 2 removable, self powered ada0 at ata0 bus 0 scbus0 target 0 lun 0 ada0: ATA-8 SATA 2.x device ada0: 150.000MB/s transfers (SATA, UDMA5, PIO 8192bytes) ada0: 152627MB (312581808 512 byte sectors: 16H 63S/T 16383C) ada0: Previously was known as ad0 SMP: AP CPU #1 Launched! Timecounter "TSC-low" frequency 12468997 Hz quality 1000 Root mount waiting for: usbus4 Root mount waiting for: usbus4 uhub4: 8 ports with 8 removable, self powered Root mount waiting for: usbus4 ugen4.2: at usbus4 Trying to mount root from ufs:/dev/ada0s3a [rw]...
前のバージョンではsysctlでCPU温度が拾えたような記憶があったのですが、見えなくなってるみたい。仕様変更かな?